Overview

Unified dual-radio 802.11ac Wave 2 2x2:2 hospitality and branch AP with internal antennas, three local Gigabit Ethernet ports, PoE out and USB host interface

Supports wall-box and desk mount deployments

Wi-Fi Radio Specifications

AP type: Indoor, dual radio, 5GHz 802.11ac 2x2 MIMO and 2.4GHz 802.11n 2x2 MIMO1

Software-configurable dual radio supports 5GHz (Radio 0) and 2.4GHz (Radio 1)

5GHz: Two spatial stream Multi User (MU) MIMO for up to 867Mbps wireless data rate to up to two (1x1 VHT80) MU-MIMO capable client devices simultaneously

5GHz: Two spatial stream Single User (SU) MIMO for up to 867Mbps wireless data rate to individual 2x2 VHT80 client devices

2.4GHz: Two spatial stream Single User (SU) MIMO for up to 300Mbps wireless data rate to individual 2x2 HT40 client devices

Support for up to 256 associated client devices per radio, and up to 16 BSSIDs per radio

Supported frequency bands (country-specific restrictions apply):

2.400 to 2.4835GHz

5.150 to 5.250GHz

5.250 to 5.350GHz

5.470 to 5.725GHz

5.725 to 5.850GHz

Available channels: Dependent on configured regulatory domain

Dynamic frequency selection (DFS) optimizes the use of available RF spectrum

Supported radio technologies:

802.11b: Direct-sequence spread-spectrum (DSSS)

802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)

Supported modulation types:

802.11b: BPSK, QPSK, CCK

802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM

Transmit power: Configurable in increments of 0.5 dBm

Maximum (conducted) transmit power (limited by local regulatory requirements):

2.4GHz band: +18 dBm per chain, +21 dBm aggregate (2x2)

5GHz band: +18 dBm per chain, +21 dBm aggregate (2x2)

Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain

Advanced Cellular Coexistence (ACC) minimizes interference from cellular networks

Maximum ratio combining (MRC) for improved receiver performance

Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance

Short guard interval for 20MHz, 40MHz and 80MHz channels

Space-time block coding (STBC) for increased range and improved reception

Low-density parity check (LDPC) for high-efficiency error correction and increased throughput

Transmit beam-forming (TxBF) for increased signal reliability and range

Supported data rates (Mbps):

802.11b: 1, 2, 5.5, 11

802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54

802.11n (2.4GHz): 6.5 to 300 (MCS0 to MCS15)

802.11n (5GHz): 6.5 to 450 (MCS0 to MCS23)

802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2 for VHT20/40/80)

802.11n high-throughput (HT) support: HT 20/40

802.11ac very high throughput (VHT) support: VHT 20/40/80

802.11n/ac packet aggregation: A-MPDU, A-MSDU

1 256-QAM modulation (802.11ac) supported by the 2.4GHz radio as well.